Will just sand the ends and reapply patches later.
The "Onkalaker" Laker 13
-
OnkaBob
- Posts: 401
- Joined: Fri Jul 18, 2008 10:12 am
- Type of boat I like: <-- Please read instructions to the left and delete this text. Then, tell us what type boat you like! :-)
- Location: Seaford, South Oz
Re: The "Onkalaker" Laker 13
Well the deck has seemed to work out OK after all that. Wet out the glass last night and apart from the very tips at bow and stern she looks reasonably neat.
Will just sand the ends and reapply patches later.
Will just sand the ends and reapply patches later.
Cheers, Bob
Laker 13 - christened and slimed (just).
Laker accessories underway.
Laker 13 - christened and slimed (just).
Laker accessories underway.
-
jem
- Site Admin
- Posts: 4916
- Joined: Fri Jun 18, 2004 8:14 pm
- Type of boat I like: Wooden
- Location: Greensboro, NC
- Contact:
Re: The "Onkalaker" Laker 13
Great!
I like the dark seam color contrast on the deck.
I like the dark seam color contrast on the deck.
-Matt. Designer.
-
Oldsparkey
- Design Reviewer
- Posts: 1272
- Joined: Sat Jun 19, 2004 11:08 am
- Type of boat I like: Wood boats .
- Location: Somewhere around Central Florida
- Contact:
Re: The "Onkalaker" Laker 13
BOB...
She is looking really good and if I may I have a suggestion about something you might want to do , either now or ( Especially) when she is ready for the water.
Keep her away from Mick or you might be missing a boat.
Chuck.
She is looking really good and if I may I have a suggestion about something you might want to do , either now or ( Especially) when she is ready for the water.
Keep her away from Mick or you might be missing a boat.
Chuck.
Remember:
Amateurs built the Ark...... Professionals built the Titanic
Visit some fine paddlers at The Southern Paddler
Amateurs built the Ark...... Professionals built the Titanic
Visit some fine paddlers at The Southern Paddler
-
OnkaBob
- Posts: 401
- Joined: Fri Jul 18, 2008 10:12 am
- Type of boat I like: <-- Please read instructions to the left and delete this text. Then, tell us what type boat you like! :-)
- Location: Seaford, South Oz
Re: The "Onkalaker" Laker 13
Now that's sheer flattery - keep it up!Oldsparkey wrote:BOB...
Keep her away from Mick or you might be missing a boat.
Anyway Mick's too busy playing with his latest "supermodel"
Cheers, Bob
Laker 13 - christened and slimed (just).
Laker accessories underway.
Laker 13 - christened and slimed (just).
Laker accessories underway.
-
Oldsparkey
- Design Reviewer
- Posts: 1272
- Joined: Sat Jun 19, 2004 11:08 am
- Type of boat I like: Wood boats .
- Location: Somewhere around Central Florida
- Contact:
Re: The "Onkalaker" Laker 13
Just a warning from one builder to another knowing how Mick thinks since he thinks along my lines ... Personally if you were over here in the southern U.S.A. I would be slipping around your place looking for it. But only for a test run , say a year or two.
Chuck.
You are doing a great job and trust me we are always looking at another boat , to add to our stable or collection.
Chuck.
You are doing a great job and trust me we are always looking at another boat , to add to our stable or collection.
Remember:
Amateurs built the Ark...... Professionals built the Titanic
Visit some fine paddlers at The Southern Paddler
Amateurs built the Ark...... Professionals built the Titanic
Visit some fine paddlers at The Southern Paddler
-
OnkaBob
- Posts: 401
- Joined: Fri Jul 18, 2008 10:12 am
- Type of boat I like: <-- Please read instructions to the left and delete this text. Then, tell us what type boat you like! :-)
- Location: Seaford, South Oz
Re: The "Onkalaker" Laker 13
Did 2 fill coats on the deck and smoothed the transition between deck glass and sides. Need some more fillcoats yet - it's amazing how you can be so careful and then still find missed patches.
Also glassed the underside of the seat and cut a small hatch in it.
Noticed a sightly pale colour on the sides and bottom of the hull. Not sure but suspect it could be blush. If so, it has taken several weeks to develop so I would still rate this as "low blush". There is still wet rubbing to do so that should take care of any blush.
Also glassed the underside of the seat and cut a small hatch in it.
Noticed a sightly pale colour on the sides and bottom of the hull. Not sure but suspect it could be blush. If so, it has taken several weeks to develop so I would still rate this as "low blush". There is still wet rubbing to do so that should take care of any blush.
Cheers, Bob
Laker 13 - christened and slimed (just).
Laker accessories underway.
Laker 13 - christened and slimed (just).
Laker accessories underway.
-
jem
- Site Admin
- Posts: 4916
- Joined: Fri Jun 18, 2004 8:14 pm
- Type of boat I like: Wooden
- Location: Greensboro, NC
- Contact:
Re: The "Onkalaker" Laker 13
It's likely a little blush. Scrub the area with some soapy water or acetone. Light sanding and it should be gone.
-Matt. Designer.
-
OnkaBob
- Posts: 401
- Joined: Fri Jul 18, 2008 10:12 am
- Type of boat I like: <-- Please read instructions to the left and delete this text. Then, tell us what type boat you like! :-)
- Location: Seaford, South Oz
Re: The "Onkalaker" Laker 13
Been getting bogged down with the detail stuff so things have been slow.
Previous post showed the seat in place. It is glued down now. This is what it looks like underneath. The ribs allowed use of only 1 thickness of ply. Flatter pieces are to support the little hatch.
Cut out the rear deck hatch yesterday - boy was I nervous about cutting into the deck. It came up OK and with a little judicious sanding/epoxying should be what I was after.
Also finished cutting out all the pieces for the coaming. They need to be tidied up before glueing on and the wide top pieces need to be reduced in width by 5mm.
She weighed in at 13.5kg (29.75lb) today. This was with 6 clamps attached so with seat pad, toggles, hatch bungies and footbraces installed it should be near 31lb.
Previous post showed the seat in place. It is glued down now. This is what it looks like underneath. The ribs allowed use of only 1 thickness of ply. Flatter pieces are to support the little hatch.
Cut out the rear deck hatch yesterday - boy was I nervous about cutting into the deck. It came up OK and with a little judicious sanding/epoxying should be what I was after.
Also finished cutting out all the pieces for the coaming. They need to be tidied up before glueing on and the wide top pieces need to be reduced in width by 5mm.
She weighed in at 13.5kg (29.75lb) today. This was with 6 clamps attached so with seat pad, toggles, hatch bungies and footbraces installed it should be near 31lb.
Cheers, Bob
Laker 13 - christened and slimed (just).
Laker accessories underway.
Laker 13 - christened and slimed (just).
Laker accessories underway.
-
Bruce36549
- Posts: 70
- Joined: Sun Dec 07, 2008 11:01 pm
- Type of boat I like: <-- Please read instructions to the left and delete this text. Then, tell us what type boat you like! :-)
- Location: Lower Alabama USA on Perdido Bay
Re: The "Onkalaker" Laker 13
Looks great, Bob! That's one you can really be proud of.
Bruce
Bruce
I may look busy, but I'm only confused.